Nissan Patrol and Ford Maverik
+ Cars of the Nissan Patrol and Ford Maverick series
+ Diagnostics of malfunctions
+ Settings and routine maintenance
- Engine
- Engine of 4.2 l
Removal and engine installation
Removal, dismantling, check of a condition and installation of assembly of yokes and bars of pushers
Removal and installation of the inlet pipeline
Removal and installation of a final collector
Service of a head of cylinders
Removal, check of a condition and service of components of a drive of the gas-distributing mechanism (chain and asterisks)
Removal, check of a condition and installation of a camshaft and pushers
Removal and installation of the pallet of a case and maslozabornik of the oil pump
Service of the oil pump
Replacement of epiploons of a cranked shaft
Service of shatunno-piston assemblies and mirrors of cylinders
Service of a cranked shaft and radical bearings
Flywheel service / driving disk
Removal and installation of support of the power unit
+ Engine of 3.0 l
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ Systems of decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Transmission
+ Coupling
+ Brake system
+ Forward and back bridges, running gear and steering
+ Body
+ Onboard electric equipment
|
Removal and installation of the pallet of a case and maslozabornik of the oil pump Removal
|
|
For performance described below procedures the tool for cutting of pillows of hermetic is required. |
|
|
Disconnect a negative wire from the battery.
To Poddomkratta a car front also establish it on props.
Turn out a drain stopper of the pallet and merge impellent oil in suitable capacity. Screw a stopper into place, having strongly tightened it.
Give bolts of fastening of the engine to intensifying arms of transmission, remove arms from the engine. Give bolts and nuts of fastening of the bottom back plate (guard) of the engine to a flywheel casing.
Gradually, in stages, give bolts of fastening of the pallet of a case of the engine. Move on a spiral from edges of the pallet to the middle.
If the pallet is established without laying, by means of the special tool cut through a pillow of sealing hermetic through which pallet fastens to an engine case. In order to avoid damages at all do not use this tool for release of the holder of a back epiploon
The pallet established on laying follows for release обстучать a hammer with soft the brisk.
|
In case of need give fixing bolts and remove from the engine a maslozabornik (see an accompanying illustration - figures marked covers of radical bearings). Will throw out a sealing ring of round section.
|
|
|
Installation
Installation is made upside-down.
|
|
Smooth out interfaced surfaces of the pallet and an engine case, having carefully removed from them all traces of a material old laying/hermetic.
Attentively examine the pallet, checking it on existence of mechanical damages. Execute necessary repair, or replace the defective pallet.
Wash out internal surfaces of the pallet and assembly of a maslozabornik by suitable solvent, having completely eliminated traces of coal deposits and шлама.
Establish a maslozabornik of the oil pump with a new sealing ring and tighten bolts of its fastening with effort of 16 ÷ 19 Nanometers.
|
|
For pallet consolidation on a case it can be used both laying, and a hermetic pillow. In case of absence of confidence of absoluteness of planeness of a landing flange originators of this Management recommend to prefer laying in order to avoid emergence in the future of the problems connected with leakages of oil. |
When using hermetic lay in a flute of a flange and round boltovy openings in it a pillow of qualitative hermetic with diameter of section 3.5 of ÷ 4.5 mm. Within no more than five minutes after overlaying of hermetic press the pallet to the block, trying not to break a pillow continuity. Then screw fixing bolts and tighten them with demanded effort in a diagonal order, moving from the center outside.
Establish intensifying arms, having tightened bolts of their fastening with demanded effort.
Fill in in the engine fresh oil, then start the engine and check it on leaks.
|
|
If for consolidation of landing of the pallet hermetic was used, start to fill in in the engine oil not earlier than what in thirty minutes after pallet installation. |
|
|
|
|