Nissan Patrol, Ford Maverick

1988-1997 of release

Repair and car operation



Nissan Patrol and Ford Maverik
+ Cars of the Nissan Patrol and Ford Maverick series
+ Diagnostics of malfunctions
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ Systems of decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Transmission
+ Coupling
+ Brake system
- Forward and back bridges, running gear and steering
   + Peredny Bridge and suspension bracket
   + Forward suspension bracket of spring type
   + the Forward suspension bracket on screw springs
   + Back bridge and suspension bracket
   + Back suspension bracket of spring type
   + the Back suspension bracket on screw springs
   - Steering
      Primary checks
      The elementary checks and adjustments
      Removal and installation of a steering wheel
      Service of a steering column
      Removal and installation of the flexible coupling of a steering shaft
      Service of assembly of the steering mechanism
      Removal and installation of the steering pump
      Service of components of a steering drive
      Removal and installation of a steering damper
      Service of the pendular lever of cross-section steering draft
      Corners of installation of forward wheels (geometry of a forward suspension bracket and steering drive)
+ Body
+ Onboard electric equipment



The elementary checks and adjustments

Effort of a tension of a driving belt of the steering pump

Correctness of adjustment of a tension of a driving belt gives a guarantee of that the last will not slip thus that at the same time is not created excessive loads both of a belt, and of pump bearings.

Measurement of effort of a tension of a belt is made in the middle of its direct site between pulleys of a cranked shaft and the steering pump. Firmly press a belt in the specified point a thumb size of a deflection should correspond to standard requirements.

Air removal from hydraulic system (pumping)

 PERFORMANCE ORDER

  1. Make sure that in the tank of system hydraulic liquid of a demanded grade (see size tables and adjustments at the end of the Management) is filled in.
  2. To Poddomkratta a car front also establish it on props.
  3. Without starting the engine, several times quickly turn a steering wheel from left to right from an emphasis against the stop. Do not hold a wheel in extreme provisions more than fifteen seconds.
  4. Check liquid level in the tank. In case of need make having added.
  5. If liquid in the tank of the steering pump is excessively saturated air (is aerated), or the raised noise background of the pump takes place, repeat performance of the procedures described in two previous paragraphs.

Removal and installation of hydraulic lines of connection of the pump of system of hydrostrengthening with the steering mechanism

After performance of the procedures, capable to cause hit to the air highway, the hydraulic system should be pumped over (see. Primary checks).

Returnable hydraulic line

 PERFORMANCE ORDER

  1. The returnable line is executed in the form of the usual steel tube connected to hoses of a high pressure by means of collars. For replacement of a hose it is necessary to weaken fixing collars then to pull together a hose from a shtutserny part of a tube.
  2. At installation of new hoses it is necessary to grease their ends from within with transmission liquid (ATF).
  3. The returnable line is connected to the steering mechanism by means of the shtutserny socket on a hollow bolt. Before starting connection of components of the socket replace copper sealing washers.

Pressure head hydraulic line

 PERFORMANCE ORDER

  1. The pressure head line represents an integral piece of a tube with the hoses tense on it. In case of leaks all line should be replaced.
  2. Give a hollow bolt of the shtutserny socket on the steering pump and disconnect the line from the last.
  3. Give bolts of arms near a pulley of a cranked shaft and the steering mechanism. Liberate the line from arms.
  4. Give a hollow bolt of the shtutserny socket on the steering mechanism and disconnect the line from the last.
  5. Remove the line from the car.

Installation is made upside-down.

Before joining of shtutserny sockets replace copper sealing washers.






;