Nissan Patrol, Ford Maverick

1988-1997 of release

Repair and car operation

Appendices

Size table and adjustments

Nominal efforts of a tightening of carving connections are given in the end of each of Appendix Sections, and also included in structure of a material of paragraphs of the text of the Management.

General technical characteristics

Characteristic	Value
Full length, mm
Versatile person (Station Wagon)	4810
Versatile person	Ti 4890
Hardtop (Hardtop)	4240
To the utility (Van) (Utility) and Mini-truck (Cab Chassis)	4970
To the utility (Van) and the Mini-truck of late years of release (since 1992) c a suspension bracket on screw springs	4700
Full width, mm
The versatile person and Hardtop (without slips on wings)	1800
The versatile person and Hardtop (with slips on wings)	1930
To the utility (Van) and Mini-truck	1690
To the utility (Van) and the Mini-truck of late years of release (since 1992) c a suspension bracket on screw springs	1930
Wheel base, mm
Versatile person, Utiliti (Van) and Mini-truck	2970
Hardtop	2400
Radius of turn, m
Versatile person, Utiliti (Van) and Mini-truck	6.7
Hardtop	5.5
Volume of a fuel tank, l
Versatile person and Hardtop	95
To the utility (Van) and Mini-truck	90
Admissible mass of the towed trailer, kg
Models of early years of release (till 1992)
The trailer equipped with brakes	2500
The trailer not equipped with brakes	750
Models of late years of release (since 1992)
The trailer equipped with brakes
The versatile person with RKPP	2800
All the others	2500
The trailer not equipped with brakes	750

Maximum corner forward свеса	42 °
Maximum corner back свеса	30 °
Maximum corner of a platform	31 °
Maximum road gleam, mm	235
Maximum admissible depth of a water barrier, mm	600

Types and volumes of greasings and liquids

All volumes are specified only approximately. Exact data can be received according to indications measuring щупов or definition through control/jellied openings.

Engine

Characteristic	Value
Type of greasing liquid	Qualities are not worse than SAE 20W/50SE
Volume of the pallet of a case, l
Engine of 4.2 l
With the filter	8.2
Without the filter	7.7
Engine of 3.0 l
With the filter	6.4
Without the filter	6.0

Cooling system

Characteristic	Value
Volume of cooling liquid (including a broad tank), l
Models of 3.0 l	11.9
Models of 4.2 l with RKPP	13.9
Models of 4.2 l with AT	13.6
Antifreeze type	Antifreeze on a basis этиленгликоля
Structure of a mix, % content of antifreeze
To - 15 ° With	30
To - 35 ° With	50

Manual transmission

Characteristic	Value
Type of greasing liquid	SAE 75W/90 GL4
Volume, l
Engine of 4.2 l	3.9
Engine of 3.0 l	3.6
Engines of 3.0 l of models of release since October, 1994.	5.1

Automatic transmission

Characteristic	Value
ATF type	Matic D
Volume, l
Early models	8.5
Models of late years of release (since 1992)	11.8

ATF Matic D is the Australian equivalent of Japanese ATF Dexron II. Use of the Australian liquid with the name Dexron II can lead to a transmission exit out of operation.

Transfer case

Characteristic	Value
Type of greasing liquid
Models of early years of release (till 1992)	SAE 75W/90 GL4
Models of late years of release (since 1992)	EFI Dexron II
Volume, l
Release models till October, 1994.
Engine of 4.2 l	2.2
Engine of 3.0 l	1.9
All models of release since October, 1994.	1.9

Forward differential

Characteristic	Value
Type of greasing liquid	SAE 80W/90 GL5
Volume, l
Models Hardtop and Versatile person	5.4
Utilitya's (Van) models and Mini-truck early years of release	4.3
Utilitya's (Van) models and Mini-truck late years of release with a suspension bracket on screw springs	5.4

Back differential

Characteristic	Value
Type of greasing liquid
Differential of usual type and with blocking	SAE 80W/90 GL5
Differential of limited sliding	SAE LS80W/90 GL5*
Volume, l
Models Hardtop and the Versatile person without differential blocking	2.1
Models Hardtop and the Versatile person with differential blocking	3.0
Utilitya's (Van) models and Mini-truck of early years of release	4.7
Utilitya's (Van) models and the Mini-truck of late years of release with a suspension bracket on screw springs	2.1

* At ambient temperature over 40 ° With use SAE LS140 GL5 liquid

Brake liquid and hydraulic liquid of coupling

Characteristic	Value
Liquid type	DOT 3

Liquid of system of hydrostrengthening of a wheel

Characteristic	Value
Liquid type	Dexron II
Volume, l	0.9 ÷ 1.0

Greasing for chassis components

Characteristic	Value
Greasing type	NLGI#2 on a lithium basis

The requirements shown to wheels and tires

Standard sizes and pressure of a rating of tires

See information шильду on the car.

If the tires established on the car are not listed among admissible on information шильде, consult about admissible modes of operation and recommended pressure of a rating at specialists of dealer office of the company manufacturer of the car.

Engine settings

All models, except 4.2 l of EFI

Characteristic	Value
Ignition order	1-5-3-6-2-4
Type of spark plugs
Engines of 3.0 l	NGK BKR6E
Engines of 4.2 l	NGK BP5ES
Interelectrode candle gap, mm	0.8 ÷ 0.9
Corner of an advancing of ignition at single turns of the engine
Models of 3.0 l
At the disconnected vacuum hose	3 ° ± 2 ° before VMT
At the connected vacuum hose	15 ° ± 5 ° before VMT
Models of 4.2 l at the connected vacuum hose
Models with RKPP	10 ° ± 1 ° before VMT
Models with AT (the selector - in situation D)	10 ° ± 1 ° before VMT
Idling turns, in a minute
Models of 3.0 l	800 ± 50
Models of 4.2 l (the AT selector - in situation D)	650 ± 50
Gap in breaker contacts (model of 4.2 l), mm	0.45 ÷ 0.55
Duration (on a corner) the closed condition of contacts of the breaker (model of 4.2 l)	34 ° ÷ 40 °
Resistive resistance of VV of wires, kiloohm	not above 30
Kompressionnoye pressure in cylinders, kPa
Standard value
Models of 3.0 l	1 196
Models of 4.2 l	1 177
The minimum admissible	883
The maximum admissible difference between cylinders	98
Gaps of valves, mm
Models of 3.0 l	Zero (hydraulic pushers with automATI chesky compensation are established)
Models of 4.2 l (the engine is heated-up, but it is switched off)	0.38

Only models of 4.2 l of EFI

At performance of adjusting procedures without fail compare the parameters specified below with given on information шильде settings of the engine, located in an impellent compartment of the car. At a different interpretation it is necessary to consider as the correct the last (with шильды).

Characteristic	Value
Type of spark plugs	BPR5E
Kompressionnoye pressure in cylinders, kPa
Standard value	1 187
The minimum admissible	892
The maximum admissible difference between cylinders	98

Engine of 4.2 l

Except late years of release equipped with fuel (EFI) injection

General parameters

Characteristic	Value
Engine type	6-cylinder, OHV
Model	ТВ42
Working volume, cm	3 4 169
Diameter of cylinders, mm	96
Course of pistons, mm	96
Ignition order	1-5-3-6-2-4
Extent of compression	8.3:1
Kompressionnoye pressure in cylinders, kPa
Standard value	1 177
The minimum admissible	883
The maximum admissible difference between cylinders	98

Head of cylinders

Characteristic	Value
Design	The integral
Material	Aluminum alloy
Admissible not planeness of an interfaced surface, mm	0.2
Height of a head, mm
The standard	117.19 ÷ 117.59
The maximum admissible depth of a frezerovka (together with the block), mm	0.2
Width of a working facet of saddles of valves, mm
The inlet	2.4 ÷ 2.8
The final	1.4 ÷ 1.9
Tilt angle of a facet of saddles of valves	45 °
Type of directing plugs of valves	The replaceable
Height of a vystupaniye of directing plugs of valves, mm	11.7 ÷ 12.3

Valves and klapanny springs

Characteristic	Value
Diameter of cores of valves, mm
The inlet	7.965 ÷ 7.980
The final	7.945 ÷ 7.960
Gap of landing of cores of valves in directing plugs, mm
The standard
The inlet	0.020 ÷ 0.053
The final	0.040 ÷ 0.073
The limiting admissible	0.1
Length of valves, mm
The inlet	116.7 ÷ 117.0
The final	117.0 ÷ 117.3
Height of a cylindrical site (corbel) of plates of valves, mm
The standard
The inlet	1.3
The final	1.5
The minimum admissible	0.5
Tilt angle of a facet of plates of valves	45 ° 30'
Free length of klapanny springs, mm
The internal	44.10
The external	49.77
Admissible limit of a tortsovka of klapanny springs, mm
The internal	1.9
The external	2.2
Assembly length of klapanny springs, mm
The internal	35
The external	40

Assembly of a drive of valves (yokes and axis of yokes)

Characteristic	Value
External Ø of an axis of yokes, mm	19.979 ÷ 20.000
Internal Ø of yokes, mm	20.020 ÷ 20.038
Gap of landing of yokes on an axis, mm	0.020 ÷ 0.059

Camshaft

Characteristic	Value
Number of bearings	7
Maximum admissible limit of a bend, mm	0.06
Limiting admissible axial люфт, mm	0.5
Gap in bearings, mm
The standard	0.20 ÷ 0.109
The limiting admissible	0.15
Diameter of bearing necks, mm
Lobby	50.721 ÷ 50.740
The second	50.521 ÷ 50.540