Nissan Patrol, Ford Maverick

1988-1997 of release

Repair and car operation



Nissan Patrol and Ford Maverik
+ Cars of the Nissan Patrol and Ford Maverick series
+ Diagnostics of malfunctions
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ Systems of decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Transmission
+ Coupling
+ Brake system
- Forward and back bridges, running gear and steering
   + Peredny Bridge and suspension bracket
   + Forward suspension bracket of spring type
   + the Forward suspension bracket on screw springs
   + Back bridge and suspension bracket
   + Back suspension bracket of spring type
   + the Back suspension bracket on screw springs
   - Steering
      Primary checks
      The elementary checks and adjustments
      Removal and installation of a steering wheel
      Service of a steering column
      Removal and installation of the flexible coupling of a steering shaft
      Service of assembly of the steering mechanism
      Removal and installation of the steering pump
      Service of components of a steering drive
      Removal and installation of a steering damper
      Service of the pendular lever of cross-section steering draft
      Corners of installation of forward wheels (geometry of a forward suspension bracket and steering drive)
+ Body
+ Onboard electric equipment





Service of the pendular lever of cross-section steering draft

Utilitya's (Van) models (Utility) and Mini-truck (Cab Chassis)

Removal and installation

For performance described below works the following special tools be required: a sensitive dinamometrichesky key (for measurement of the initial moment of a provorachivaniye of the pendular lever); a special stripper of a soshka of the steering mechanism (for removal of the pendular lever).

Removal

 PERFORMANCE ORDER

    To Poddomkratta a car front also establish it on props. Remove шплинты, then give koronchaty nuts of fastening to assembly of the pendular lever longitudinal and cross-section the helmsman of drafts. If the stripper available is not available, liberate spherical fingers of assembly of the pendular lever by means of an alternative method with use of two hammers. Give bolts of fastening of assembly of the pendular lever of cross-section steering bent for of the chassis and remove assembly from the car.

Installation

Installation is made upside-down.

 PERFORMANCE ORDER

    Tighten bolts of fastening of assembly with effort of 45 ÷ 55 Nanometers. The nominal effort of a tightening of koronchaty nuts makes 88 ÷ 113 Nanometers. Shplinta are subject to replacement without fail. In the conclusions by means of the lubricant gun grease assembly of the pendular lever by greasing of a demanded grade.

Dismantling

 PERFORMANCE ORDER

    Remove assembly of the pendular lever of cross-section steering draft from the car. Strongly clamp assembly in a vice with soft sponges. Remove шплинт and give a fixing nut (components of assembly are shown on an accompanying illustration). By means of a stripper of a soshka of the steering mechanism remove the pendular lever from the axis.
1 — шплинт
2 — a nut
3 — the pendular lever
4 — an epiploon
5 — a casing
6 — plugs
7 — an axis
8 — a spring
9 — a plate of a spring
10 — laying
11 — a cover
12 — bolts
    Give bolts of fastening of a cover of the pendular lever to a casing. Remove a spring with its plate, will throw out laying. Take an axis from a casing and remove the top plug. By means of a suitable drift and a hammer carefully beat out an epiploon from the bottom end face of a casing, then remove the bottom plug.

Cleaning and check of a condition of components

 PERFORMANCE ORDER

    Wash out all components of assembly in suitable solvent, then carefully dry them. Examine an assembly casing on existence of cracks and other damages. Check a condition of an axis, a casing and plugs. In case of detection of signs of wear or damages replace defective components. Check a condition (degree of wear and weakening of effort of compression) springs. Examine the lever on existence of cracks and other damages.

Assembly

Assembly is made as it should be, the return to a dismantle order.

 PERFORMANCE ORDER

    Establish in a casing of the pendular lever of the plug. Grease a new epiploon outside with suitable hermetic, then plant it by means of an opravka from below in a casing. Grease epiploon sponges with universal greasing. Grease with universal greasing contacting surfaces of plugs of a casing and an axis, then insert an axis into a casing Establish a plate and a spring. Track, that uvulas of a plate of a spring correctly settled down in a casing. Establish a cover of a casing of the pendular lever with new laying, strongly tighten fixing bolts. Dress the lever on an axis, strongly tighten a fixing nut and fix its shplinty. Measure an initial torque of a provorachivaniye of the pendular lever:
      Grasp the lever and move it forward-back in a range about 90 ° for greasing distribution. Dress on a nut of an axis of the lever a replaceable face head. Connect to a head a sensitive dinamometrichesky key and, putting to a key collar effort, consider torque size at the moment of a lever stragivaniye from a place. The nominal rate makes 4.9 Nanometers. If the result of measurement does not correspond to demanded value, the lever it is necessary to disassemble and eliminate the zakusyvaniye reason.