Nissan Patrol, Ford Maverick

1988-1997 of release

Repair and car operation



Nissan Patrol and Ford Maverik
+ Cars of the Nissan Patrol and Ford Maverick series
+ Diagnostics of malfunctions
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ Systems of decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Transmission
+ Coupling
+ Brake system
+ Forward and back bridges, running gear and steering
+ Body
- Onboard electric equipment
   The elementary diagnostic equipment and examples of its application
   Removal and installation of the press button of a horn
   Switches
   Alarm and lighting devices
   Removal and installation of a combination of devices
   Service of the sensor of a speedometer
   Audiosystem service
   Removal and installation of the motor of the fan of a heater
   Service of cleaners of a windscreen
   Service of a cleaner of back glass
   Safety locks, fusible inserts and relay
   Electroconducting of a food of electric equipment of the trailer
   Schemes of electric connections
   + Appendices





Electroconducting of a food of electric equipment of the trailer

General information

Some types of farkopny sockets with a various arrangement of plugs in them are issued. The most widespread is the 7-contact socket providing formation of two additional contours, usually used for food giving on fires of a backing and electric brake mechanisms of the trailer.

At the turnbuckle equipment probably it is necessary to replace the former breaker of indexes of turns with more powerful for the purpose of a podderzhivaniye stipulated in traffic regulations of frequency of a blinking of signal lights accepted in the concrete region. The authorities of some regions order also obligatory installation on the dashboard of control repeaters of indexes of turns.

If the reception nest of the farkopny socket does not correspond on a standard size to the tip established on the trailer, it is necessary to get one of suitable let-out transitional nozzles (see an accompanying illustration).

1 — for a pristykovka of the tip of the Brylite type to a Utilux type nest
2 — for a pristykovka of the 6-contact tip of the Utilux type to a 5-contact nest of the Utilux type

Installation of the farkopny socket

For the equipment of the hook-on device the reception nest of the farkopny socket required (on a minimum): corresponding to the trailer tip a reception nest, a basic arm, 7-жильный the flexible cable, the isolated sockets for connection of wires and the rubber plug through passage.

Necessary components for the equipment of power supply of the trailer with use of the farkopny socket of the Utilux type.

1 — the tip
2 — - terminal blocks
3 — - a boot
4 — - a boot
5 — - screws
6 — - a nest
7 — - the socket for connection of wires
8 — - a wire
9 — - the plug through passage,
10-7 — - a zhilny flexible cable
11 — - the control repeater
12 — - the screw
13 — - a basic arm
14 — - a lamp

 PERFORMANCE ORDER

    Disconnect a negative wire from the battery. Find a plait of electroconducting of lamps in a back part of the car. Find wires of a food of the right and left back indexes of turns, back marker lights, stoplights, fires of a backing and weight. Using the schemes of electric connections provided in the end of this Chapter, define color marking of each of the listed wires. By means of the isolated sockets connect 7-жильный a flexible cable to each of the found wires. In case of use of the farkopny socket of 7-contact type adhere to the following standard scheme of the color coding:

plug No.

Contour

Color

1

Lamp of the index of the left turn

The yellow

2

Lamp of fire of a backing

The black

3

Weight

The white

4

Lamp of the index of the right turn

The green

5

Electric brakes

The dark blue

6

Stoplight lamp

The red

7

Lamp of a marker light

The brown

    In case of use of the farkopny socket of 6-contact type adhere to the following standard scheme of the color coding:

plug No.

Contour

Color

1

Lamp of a marker light

The brown

2

Lamp of the index of the left turn

The yellow

3

Lamp of the index of the right turn

The green

4

Stoplight lamp

The red

5

Auxiliary contour

The dark blue

6

Weight

The white

    In case of use of the farkopny socket of 5-contact type adhere to the following standard scheme of the color coding:

plug No.

Contour

Color

1

Lamp of the index of the left turn

The yellow

2

Weight

The white

3

Lamp of the index of the right turn

The green

4

Stoplight lamp

The red

5

Lamp of a marker light

The brown

    Drill in the panel of a floor of the car a suitable opening and establish in it the rubber plug through passage.

Before boring through an opening, whether check it is impossible to use any of already available technological. The plug through passage should be established without fail in order to avoid wiping of wires.

    Pass in an opening with the established plug 7-жильный through passage a flexible cable. Cut off a cable for the demanded length and put on it a boot. Smooth out each of cable veins from isolation approximately on 15 mm. Connect cable veins to plugs of a reception nest, observing the standard color scheme and following instructions of manufacturers of the socket. Collect a nest and establish on its back end a boot. Components of the 7-contact farkopny socket of the Brylite type are shown on an accompanying illustration.
1-7 — a zhilny flexible cable
2 — covers
3 — a nest
4 — a boot
5 — the tip
6 — screws
    Establish a basic arm as it is possible closer to a spherical finger of the hook-on device and it is rather high to observe a road gleam of the car. Establish in an arm a reception nest of the socket. Connect the trailer tip to a reception nest of a turnbuckle for check of serviceability of their joining.

Installation of the tip of the trailer

For the trailer equipment the tip of the farkopny socket required (on a minimum): corresponding to a reception nest of the socket on the car the tip, 7-жильный a flexible cable and the isolated sockets for connection of wires.

Procedure of installation of the tip on the trailer is similar that for installation of a reception nest of the socket on the car, taking into account listed below the moments.

 PERFORMANCE ORDER

    Connection of electroconducting of the trailer to the tip of the socket make according to the standard standard of color marking. Follow instructions of manufacturers of the socket. If free length of a plait of wires of the trailer it appears insufficiently, increase a plait with the help 7-жильного a flexible cable and the isolated sockets for connection of wires. If the color scale of electroconducting of the trailer does not correspond to the standard standard, identify each of wires, for what:
      Find a wire of weight of the trailer; Connect a wire crossing point from the negative plug of the 12-voltny battery to a weight wire; Connect a wire crossing point to the positive plug of the battery and serially connect to it each of wires of a plait of the trailer. Write down color of each wire and the device which has worked at its connection (an alarm fire/brake).
    After completion of installation connect the tip to a reception nest of a turnbuckle on the car for check of serviceability of joining of components of the socket.