Switches Removal and installation of the lock of ignition
|
|
Disconnect a negative wire from the battery.
Give fixing screws and remove the bottom casing of a steering column.
Give the screw of fastening of assembly of the lock of ignition (and components of the lock of ignition are shown to a detail of fixture on an accompanying illustration).
Disunite the electric socket and remove from the lock the ignition switch.
|
|
Installation is made upside-down. Removal and installation of the combined podrulevy switch Removal
|
|
Disconnect a negative wire from the battery.
Remove facing of the lock of ignition.
Give fixing screws and remove the bottom casing of a steering column.
Remove a steering wheel and the press button of a horn.
Remove the top casing of a steering column.
Disunite electric sockets of the combined podrulevy switch.
|
|
Weaken the screw of a collar of fastening of the combined switch (see an accompanying illustration).
|
Push the switch towards the dashboard, slightly turn it and remove from a steering column.
|
|
Installation Installation is made upside-down. Track, that the landing ledge of the switch got to a reciprocal opening, after it tighten the collar screw. Removal and installation of the switches located on a guard of a combination of devices
|
|
On the bottom finishing panel of facing of an instrument guard the potentiometer of intensity of illumination of devices, the switch of heating of back glass and (are located at the corresponding complete set) the switch of modes of a cleaner/washer of back glass. |
Removal
|
|
Disconnect a negative wire from the battery.
|
|
Having carefully hooked a screw-driver (enclose under her sting a cardboard plate for protection of the panel), take from the panel the corresponding switch (see an accompanying illustration).
|
Disconnect behind electroconducting and remove the switch.
|
|
Installation Installation is made upside-down. Track quality of contacts and reliability of fastening of the electric socket on the back party of the switch. Removal and installation of the switch of the alarm system
|
|
Disconnect a negative wire from the battery.
Remove the central part of the dashboard.
Wring out one of fixing clamps, push the switch forward and remove it from the central panel.
|
|
Installation is made upside-down. Replacement of the breaker of indexes of turns
|
| |
The block of the breaker of indexes of turns is located under the dashboard, near an axis of a pedal of a brake (see an accompanying illustration). |
|
|
|
Disconnect a negative wire from the battery.
Disunite the electric socket of the breaker.
Give screws of fastening of an arm of the breaker and remove the block together with an arm from the car.
|
|
Installation is made upside-down. Removal and installation of the switches located on the central part of the dashboard
|
|
The number located in the central part of the dashboard includes the switch of the electric drive of the aerial of a radio receiver, the switch of the back conditioner, the switch of a drive of the top hatch and switches of blocking of differentials. |
|
|
Disconnect a negative wire from the battery.
Having carefully hooked a screw-driver (enclose under her sting a cardboard plate for protection of the panel), take from the panel the corresponding switch.
Disconnect behind electroconducting and remove the switch.
|
|
Installation is made upside-down.
Removal and installation of switches of the central lock and electric drive of window regulators
Removal
|
|
Disconnect a negative wire from the battery.
Having carefully hooked a screw-driver, take the switch from the panel of furnish of a door.
Disunite behind the electric socket and remove the switch.
|
|
Installation
Installation is made upside-down.
Track quality of contacts and reliability of fastening of the electric socket on the back party of the switch.
Removal and installation of the switch of the electric drive of a rear-view mirror
Removal
|
|
Disconnect a negative wire from the battery.
Having carefully hooked a screw-driver (enclose under her sting a cardboard plate for protection of the panel), take from the dashboard the corresponding switch (see an accompanying illustration).
Disunite behind the electric socket and remove the switch.
|
|
Installation
Installation is made upside-down.
Track quality of contacts and reliability of fastening of the electric socket on the back party of the switch.
Service of the sensor switch of stoplights
| |
The sensor switch of stoplights is located on an arm of a pedal of a brake under the dashboard (see an accompanying illustration). |
Check of serviceability of functioning
|
|
Squeeze out a pedal of a brake and make sure of inclusion of stoplights.
If stoplights do not work, disconnect from the sensor switch electroconducting.
Establish a wire crossing point between plugs of the electric socket. If now there was an inclusion of stoplights, it is necessary to make sensor switch adjustment, or to replace it with the serviceable.
|
|
Removal and installation
Removal
|
|
Disconnect a negative wire from the battery.
Disconnect from the sensor switch electroconducting.
Weaken a lock-nut and remove the sensor switch from an arm of a pedal of a brake.
|
|
Installation
Installation is made upside-down.
|
|
Track quality of contacts and reliability of fastening of the electric socket on the back party of the switch.
Execute sensor switch adjustment.
|
|
Adjustment
|
|
Adjust free height of a pedal of a brake.
Weaken the switch and adjust its situation. Try to achieve between an emphasis and an end face of a carving part of the sensor switch of a gap in 0.3 ÷ 1.0 mm.
|
|
Removal and installation of the sensor switch of permission of start (only models of 3.0 l)
|
|
Disconnect a negative wire from the battery.
Disconnect from the sensor switch electroconducting.
Weaken a lock-nut and remove the sensor switch from a pedal arm.
|
|
Installation is made upside-down.
Removal and installation of the sensor switch of a control lamp of the cocked position of the lever of the parking brake
|
|
Give screws of fastening of the central console and slightly raise the lever of the parking brake. Remove the central console from the car.
|
|
Give a fixing bolt and disconnect from the sensor switch of a control lamp electroconducting (location of the sensor switch is shown on an accompanying illustration - the central console is removed).
|
Remove the sensor switch from the car.
|
|
Installation is made upside-down.
Service of the sensor switch of fires of a backing (only models with RKPP)
|
|
The sensor switch of fires of a backing is located on transmission. Adjustment of the sensor switch is not provided. |
Check of serviceability of functioning
|
|
Disconnect a negative wire from the battery.
By means of an ohmmeter make sure that the sensor switch will close (conductivity) takes place when switching box on a reverse gear. At a box conclusion from the provision of a reverse gear the sensor switch should appear will open (conductivity is absent).
Replace the faulty sensor switch.
|
|
Removal and installation
Removal
|
|
To Poddomkratta the car also establish it on props.
Disunite electric sockets and remove the sensor switch from transmission.
|
|
Installation
Installation is made upside-down.
|
|
Before installation grease a sensor switch carving with firm hermetic.
Track quality of contacts and reliability of fastening of the electric socket of the sensor switch.
|
|
Service of the sensor switch of a control lamp of inclusion of an all-wheel drive mode
| |
The sensor switch of a control lamp of a 4WD mode is fixed on a transfer case (see an accompanying illustration). Adjustment of the sensor switch is not provided. |
Check of serviceability of functioning
|
|
Disconnect a negative wire from the battery.
By means of an ohmmeter make sure available conductivity of the sensor switch at inclusion of modes H and the L 4WD of a transfer case. In other the provision of a box conductivity should be absent.
In case of need replace the sensor switch.
|
|
Removal and installation
Removal
|
|
To Poddomkratta the car also establish it on props.
Disunite electric sockets and remove the sensor switch from a transfer case.
|
|
Installation
Installation is made upside-down.
|
|
Before installation grease a sensor switch carving with firm hermetic.
Track quality of contacts and reliability of fastening of the electric socket of the sensor switch.
|
|
Removal and installation of sensors switches of illumination of salon when opening doors
|
|
Completely open a door and remove from the door sensor switch a protective cover.
Give the fixing screw and partially take the sensor switch from a door.
|
|
Disconnect electroconducting (see an accompanying illustration) and remove the sensor switch from the car.
|
|
|
Installation is made upside-down. |