Nissan Patrol and Ford Maverik
+ Cars of the Nissan Patrol and Ford Maverick series
+ Diagnostics of malfunctions
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ Systems of decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Transmission
+ Coupling
+ Brake system
- Forward and back bridges, running gear and steering
+ Peredny Bridge and suspension bracket
+ Forward suspension bracket of spring type
+ the Forward suspension bracket on screw springs
+ Back bridge and suspension bracket
+ Back suspension bracket of spring type
- Back suspension bracket on screw springs
Service of shock-absorbers
Removal and installation of screw springs of a back suspension bracket
Removal and installation of a cross-section jet bar
Removal and installation of longitudinal jet bars of a suspension bracket
Removal and installation of the stabilizer of cross-section stability
Removal and installation of assembly of the mechanism of shutdown of the back stabilizer of cross-section stability
+ Steering
+ Body
+ Onboard electric equipment
|
Removal and installation of longitudinal jet bars of a suspension bracket
|
|
For performance described below procedures the press, suitable opravka and pipes be required. |
Removal Top jet bar
|
|
To Poddomkratta a car back from the relevant party also establish it on the props got under a frame of the chassis and assembly of the back bridge.
In case of need remove the corresponding back wheel.
Give a nut of a bolt of fastening of a jet bar to a bridge arm. Try not to damage thus brake lines.
Give a nut of a bolt of fastening of a jet bar to an arm of a frame of the chassis.
Take bolts, having beaten out them by means of a brass drift (support a bar in the course of knocking-out of bolts). The longitudinal jet bar of a back suspension bracket with details of fixture is shown on an accompanying illustration.
Remove a jet bar from the car.
Examine a jet bar on existence of cracks and deformation signs, in case of need make replacement.
Check a condition of plugs in a jet bar. Defective plugs replace:
Prop up a bar under the plug subject to replacement with a piece of a pipe of suitable diameter (the plug should pass freely through a pipe).
By means of the tool which opravka will rest against an external steel tube of the plug, squeeze out the plug of a bar.
Moisten an external surface of the new plug with soap water and start to push gradually the plug on a svoyeposadochny place by means of a piece of a pipe which will rest against an external steel tube of the plug.
Make sure of perpendicularity of landing of the plug and centrality of its arrangement.
|
|
Bottom longitudinal jet bar
|
|
To Poddomkratta a car back from the relevant party also establish it on the props got under a frame of the chassis and assembly of the back bridge.
Remove the corresponding back wheel.
Give a nut of a bolt of fastening of a jet bar to a bridge arm.
Give a nut of a bolt of fastening of a jet bar to an arm of a frame of the chassis.
Take bolts, having beaten out them by means of a brass drift (support a bar in the course of knocking-out of bolts).
Remove a jet bar from the car, having remembered its adjusting situation - the ends of a bar are slightly displaced.
Examine a jet bar on existence of cracks and deformation signs, in case of need make replacement.
Check a condition of plugs in a jet bar. Defective plugs replace:
Prop up a bar under the plug subject to replacement with a piece of a pipe of suitable diameter (the plug should pass freely through a pipe).
By means of the tool which opravka will rest against an external steel tube of the plug, squeeze out the plug of a bar.
Moisten an external surface of the new plug with soap water and start to push gradually the plug on the seat by means of a piece of a pipe which will rest against an external steel tube of the plug.
Make sure of perpendicularity of landing of the plug and centrality of its arrangement.
|
|
Installation Installation is made upside-down.
|
|
If replacement of plugs is made, attentively check a condition of axial bolts of bars. Worn-out components replace.
Establish a jet bar on the car, establish fixture (nuts, washers and rubber plugs), but do not tighten it finally at this stage. Lower the car on the earth.
Several times rock the car for a usadka of components of a suspension bracket, then tighten a nut of fastening of a bar to a chassis frame with effort of 147 ÷ 177 Nanometers.
Nuts of fastening of bars to the bridge tighten with effort of 98 ÷ 137 Nanometers.
|
|
|
|