Nissan Patrol and Ford Maverik
+ Cars of the Nissan Patrol and Ford Maverick series
+ Diagnostics of malfunctions
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ Systems of decrease in toxicity of the fulfilled gases
+ Systems of electric equipment of the engine
+ Transmission
+ Coupling
+ Brake system
+ Forward and back bridges, running gear and steering
- Body
Care of a body
Removal of spots of a various origin from a vinyl upholstery and panels of furnish of salon
Care of an upholstery and salon rugs
Repair of insignificant damages of body panels
Repair of considerable damages of a body
Replacement of a windscreen and the fixed windowpanes
Service of forward doors
Service of back doors
Removal and cowl installation
Service of doors of a back of models Hardtop (Hardtop) and Versatile person (Station Wagon)
Service of a door of a back of models of Utilitya (Van) (Utility)
Removal and front grille installation
Removal and installation of the central console
Removal and installation of forward seats
Removal and installation of a back seat
Service of seat belts
Removal and dashboard installation
+ Onboard electric equipment
|
Service of back doors Removal and installation of the panel of furnish and internal handles
Removal
|
|
Give the screw of fastening of facing of the handle of a remote drive of the lock to the door panel. Remove facing.
On models with a manual drive of lowering-podnimaniya of door glasses remove the window regulator handle by means of the tool for removal of clamps. In the absence of available this tool hook a facing overlay of the handle the thin strong wire bent on the end in the form of a hook. Lower a hook in a clamp under the driving handle and, having pulled for a wire, take a clamp from a handle end face then remove the handle from a door. Alternatively the handle can be removed by means of the strong matter got under it. For extraction of a clamp it is necessary to pull strongly for fabric corners.
On models with a separate armrest give fixing screws and remove an armrest from a door.
On models with electric window regulators with individual switches remove the switch from the panel of furnish of a door and disunite its electric socket. Try not to damage the switch panel.
On models with built in an armrest the switch of a window regulator operate as follows:
Remove a finishing slip from the lower part of the zakhvatny handle of a door and give the screws located under it. A screw-driver with a flat sting carefully hook the zakhvatny handle and remove it from armrest assembly.
Screw-driver with a flat sting carefully hook the panel of the switch of a window regulator and take the last from armrest assembly. Disunite the electric socket and take the switch panel aside from a working zone.
Give screws of fastening of an armrest to the internal panel of a door. Leave an armrest connected to the panel of furnish of a door.
|
|
Insert a screw-driver with a thin wide flat sting between the panel of furnish and a door frame as it is possible closer to one of clamps. Hooking, serially take clamps of fastening of the panel of furnish. Remove the panel from a door (the back door with removed by the panel of furnish and a sealing film is shown on an accompanying illustration).
|
Carefully remove a polymeric sealing film from the internal panel of a door.
|
|
Installation
Installation is made upside-down.
|
|
Track correctness of placement on the panel of a door a polymeric sealing film. Torn or otherwise damaged film it is better to replace.
Replace the damaged clamps of the finishing panel.
Accurately establish the furnish panel on a door, serially latching clamps.
On models with a manual drive of lowering-podnimaniya of glasses establish on a door a finishing overlay of the handle of the window regulator, the handle and its clamp. Track, that mutual position of the handle and a windowpane corresponded to that on an opposite door.
|
|
|
|
The clamp of the handle of a window regulator should be established in the handle before the last will be put on a pin of a shaft of a regulator. |
Removal and installation of a windowpane and motionless glass of a back door
Removal
Components of door glass and mechanism of its drive
|
|
Remove internal handles, the panel of furnish of a door and a polymeric sealing film of a door.
Operating through an opening in the door panel, give screws of fastening of a windowpane to ползуну a window regulator. Carefully lower glass against the stop in a bottom of a frame of a door.
Find clamps of fastening of an internal rubber sealing tape to the top part of a lath of a belt of the internal panel of a door. Grasp a sealing tape near clamps and push it outside, serially releasing clamps. Continue work before complete liberation of a tape from a lath of a door belt. Take a tape aside.
Find clamps of fastening of an external sealing tape to the top part of the external panel of a door on bottom edge of a window aperture. Lift a tape around an arrangement of clamps, serially taking the last before complete liberation of a tape from a door.
Delay back a site of a rubber sealant from external edge of a window frame directly over a back directing trench. Give the screw of fastening of a trench to a transom.
Give bolts of fastening of a back directing trench to an internal frame of a door.
Turn a back directing trench on 90 ° and take it from a door at the top.
By means of the assistant advance on a transom motionless glass. Watch uniformity of distribution of pressing on the top and bottom edges of glass. Take motionless glass together with a sealant from a transom.
Take from a door elevating glass. Put it on a soft surface.
|
|
Installation
Installation is made upside-down.
|
|
Check a condition of a sealant of motionless glass. In case of need make replacement.
Adjust position of a back directing trench, achieving smoothness of lowering-podnimaniya of a windowpane.
Having freely fixed screws bottom edge of a windowpane on ползуне a window regulator, lift glass, having densely pressed it to the top back corner of an aperture and to a back directing trench. Having fixed glass in this situation, finally tighten screws.
Before establishing into place a polymeric sealing film and the panel of furnish of a door, check serviceability of functioning of mechanisms of the lock and a window regulator.
|
|
Removal and installation of a regulator of a window regulator
Removal
|
|
Remove internal handles of a door, the panel of furnish and a polymeric sealing film.
Remove a windowpane. Alternatively glass can be fixed in the lifted situation by means of wedges, previously having given screws of fastening it to ползуну a window regulator.
On models with electrodriving window regulators disunite the electric socket of a regulator.
Give bolts of fastening of a regulator to the internal panel of a door. Take regulator assembly through an opening of access in the internal panel of a door.
|
|
Installation
Installation is made upside-down.
|
|
Before installation grease a regulator with universal greasing.
Adjust the provision of a windowpane.
Before establishing into place a polymeric sealing film and the panel of furnish of a door, check serviceability of functioning of mechanisms of the lock and a window regulator.
|
|
Removal and installation of the door lock and drive of remote control by it
Removal
Components of a drive of the door lock
|
|
Remove internal handles of a door, the panel of furnish and a polymeric sealing film.
Give screws of fastening of the internal handle of a remote drive of the lock of a door to the internal panel of a door.
Disconnect a rod of a remote drive from the lock. Remove a rod with the handle from a door.
Disconnect from the lock a rod of the button of switching off.
On models with the central lock disconnect from a latch an executive rod of the driving motor.
Give screws of fastening of the mechanism of the lock to a door. Take the lock mechanism from a door through an access opening.
|
|
Installation
Installation is made upside-down.
|
|
Before installation grease the lock mechanism with universal greasing.
Rotating a nut on an executive rod of the external handle of a door, adjust a gap between a nut and the lock lever - at the released handle the gap should make 0.5 ÷ 1.5 mm.
Before establishing into place a polymeric sealing film and the panel of furnish of a door, check serviceability of functioning of mechanisms of the lock and a window regulator.
|
|
Removal and installation of the external handle of a door
Removal
|
|
Completely lift a windowpane and remove internal handles of a door, the panel of furnish and a polymeric sealing film.
Disconnect an executive rod of the lock from the external handle of a door, having liberated it from a plastic clamp.
Give nuts of fastening of the handle to the external panel of a door. Remove the handle.
|
|
Installation
Installation is made upside-down.
|
|
Check a condition of a sealant of the external handle of a door. In case of need replace a sealant.
In case of need replace a clamp of an executive rod.
Adjust the provision of a nut of an executive rod of the external handle, achieving a gap between it and the lock lever in 0.5 ÷ 1.5 mm (at the released handle).
Before establishing into place a polymeric sealing film and the panel of furnish of a door, check serviceability of functioning of mechanisms of the lock and a window regulator.
|
|
Replacement and adjustment of a plate of the drummer of the lock
|
|
Mark with a marker the provision of a plate of the drummer on a door pillar (location of a plate is shown on an accompanying illustration).
Turn out adjusting screws and remove a drummer plate. Check a condition of details, defective replace.
Installation is made upside-down.
Place a drummer plate on a rack according to the landing labels put in the course of dismantle. Screw adjusting screws and tighten so that the plate stayed put.
Cover a door, then densely realize it.
Lift the external handle and carefully open a door, trying not to displace a drummer plate.
Tighten screws and again close a door, checking serviceability of functioning of the lock and a drummer plate. If there is a need for further adjustment, weaken adjusting screws and displace a drummer plate in the demanded direction, achieving trouble-free operation of the lock when opening and closing door.
On termination of adjustment strongly tighten adjusting screws of a plate.
|
|
|
|