Nissan Patrol and Ford Maverik + Cars of the Nissan Patrol and Ford Maverick series + Diagnostics of malfunctions + Settings and routine maintenance + Engine + Systems of cooling, heating and air conditioning + the Power supply system and production of the fulfilled gases + Systems of decrease in toxicity of the fulfilled gases - Systems of electric equipment of the engine - Ignition system Electric checks Service of the distributor of ignition + charge and start Systems + Transmission + Coupling + Brake system + Forward and back bridges, running gear and steering + Body + Onboard electric equipment
|
Service of the distributor of ignition Removal and installation Removal
|
- Disconnect a negative wire from the battery.
- Uncover the distributor assembled VV wires.
- Disconnect from the distributor electroconducting and a vacuum hose of the proof-reader of ignition.
- Turn the engine clockwise so that the begunok turned a nouse towards an arrangement of the plug of a candle wire of the first cylinder. Make sure of combination of distributive labels on the engine.
- Mark position of the case of the distributor in relation to a head of cylinders, then give a fixing bolt and remove the distributor. Try to remember in what direction the begunok was turned and fix its final situation.
|
|
Installation Installation is made upside-down.
|
- Check a condition of a sealing ring (rings) of the distributor, replace the defective.
- If the engine was turned after distributor extraction, turn of a cranked shaft bring the piston of the first cylinder into the situation close to the provision VMT of the end of a step of compression, then achieve combination of a label of VMT of a cranked shaft with a zero mark of a distributive scale on a cover of a drive of the gas-distributing mechanism.
|
If to turn out a spark plug of the first cylinder and to clamp a candle opening a finger, at piston approach to the provision VMT of the end of a step of compression there will be a distinct feeling of pressure. |
- If the engine was not turned, establish a begunok in a starting position (which it occupied after from extraction from the engine) and establish the distributor in a head of cylinders, achieving combination of landing labels. Screw a fixing bolt.
- Connect to the distributor electroconducting and a vacuum hose and execute installation of a corner of an advancing of ignition.
|
|
Dismantling Models of 3.0 l
|
- Give the fixing screw and remove a begunok. Remove the screen of the limiter of turns and sealing rings (see an accompanying illustration).
- Disconnect electroconducting from the control unit. Give fixing screws and take from the distributor a plait of wires.
- Give fixing screws and remove a stator and a magnet (internal components of the distributor are shown on an accompanying illustration).
- Having hooked two screw-drivers, remove a rotor of the sensor of ignition from a shaft, take a cylindrical pin. Remember the adjusting provision of a rotor.
- Give the remained screws of fastening of the block of the vacuum proof-reader. Remove an E-shaped clip and remove the block from the distributor.
- Give fixing screws and remove from the distributor a basis plate.
- Supporting a driving gear wheel of the distributor, give the screw of fastening of a shaft of a rotor of the sensor of ignition. Take a shaft from the distributor case.
- Mark adjusting provisions of springs and грузиков the proof-reader of an advancing of ignition.
- Disconnect and remove springs.
- Remove E-shaped clips and remove грузики the proof-reader.
|
|
Models of 4.2 l
Distributor components
|
- Give fixing screws and remove a begunok from a distributor shaft. Remove the screen of switching of the limiter of turns and sealing rings.
- Give fixing screws and remove from the distributor a plait of wires.
- Give remained fixing and remove assembly of contacts of the breaker from the distributor.
- Give fixing screws and remove from the distributor a grounding wire.
- Give the remained screws of fastening of the block of the vacuum proof-reader. Remove an E-shaped clip and take the vacuum proof-reader from the distributor.
- Give fixing screws and remove a basis plate from the distributor.
- Supporting a driving gear wheel, give the screw of fastening of a cam. Take a cam from the distributor case.
- Mark adjusting provisions of springs and грузиков the proof-reader of an advancing of ignition.
- Disconnect and remove springs.
- Remove E-shaped clips and remove грузики the proof-reader.
|
|
Cleaning and condition check
|
- Carefully wash out all components, except for electric knots and the block of the vacuum proof-reader of an advancing of ignition, in suitable solvent.
- Estimate degree of wear of the bottom shaft and the distributor case. In case of need make replacement.
- Check a cam, грузики and springs on existence of signs of wear and damages. In case of need make replacement.
- Check on wear and damages a basis plate. In case of need replace.
- On models of 4.2 l check breaker contacts on existence of signs of wear and cavities. In case of need make replacement.
|
At installation of new assembly of contacts of the breaker surely replace also the condenser. |
- Check a distributor cover, a begunok and the screen of the limiter of turns on existence of cracks, coal paths, прогаров and traces of corrosion of plugs.
- Estimate degree of wear of the central piece of coal. Measure size of its vystupaniye.
- Check the block of the vacuum proof-reader on existence of signs of leaks through a diaphragm for what press on connecting draft, press a finger to a soaking-up tube, then release draft. Depression under a finger should keep within at least 30 seconds.
- Check a condition of sealing rings, replace the defective.
- Estimate degree of wear of a driving gear wheel.
|
|
Assembly Models of 3.0 l Assembly is carried out as it should be, the return to a dismantle order.
|
- Moderately grease with high-temperature greasing of an axis грузиков, springs and drafts of the vacuum proof-reader of an advancing of ignition.
- Establish грузики and springs according to the labels put in the course of dismantle. Fix them E-shaped clips.
- Establish a shaft of a rotor of the sensor of ignition, screw the fixing screw.
- Establish a basis plate, fix it screws.
- Establish the block of the vacuum proof-reader of an advancing of ignition and an E-shaped clip.
- Establish a plait of wires, fix it screws. Screw screws of fastening of the block of the vacuum proof-reader.
- Adjust an air gap.
- Establish the screen of the limiter of turns and sealing rings.
- Establish a begunok, fix it the screw.
- Establish the distributor on the engine.
|
|
Models of 4.2 l
|
- Moderately grease with high-temperature greasing of an axis грузиков, springs and drafts of the vacuum proof-reader of an advancing of ignition.
- Establish грузики and springs according to the labels put in the course of dismantle. Fix them E-shaped clips.
- Establish a cam and fix it the screw.
- Establish a basis plate, do not roll fixing screws at this stage.
- Establish the block of the vacuum proof-reader of an advancing of ignition and an E-shaped clip.
- Establish a wire of grounding and screw screws of fastening of a plate of the basis.
- Establish assembly of contacts of the breaker and fix it screws.
- Establish a plait of wires, fix it screws. Screw screws of fastening of the block of the vacuum proof-reader.
- Adjust a gap in breaker contacts.
- Establish the screen of the limiter of turns and sealing rings.
- Establish a begunok, fix it the screw.
- Establish the distributor on the engine.
|
|
|
;
|